To make your room look beautiful with elegant Baseboard Molding in Miami, it is required that the installation along with the finish is perfect so that nothing striking to the eyes is left behind. Therefore, when you install such baseboards, you should keep in mind the simple procedures to do it and follow it as well. To start with, you should have the required tools which consist of a tree-square, caulking gum, pencil, hammer, nails, sand paper, and miter saw along with the wood filler. Find out the longest wall and then cut each end of the baseboard at ninety degrees it you sue one single baseboard to fit into the perpendicular ends of the walls.
Use Scarf Joint Method
When you have to use more than one baseboard for the longest wall, then it is best done with the scarf joint method. You have to make the cuts at an angle of forty-five degrees for scarf joints in Baseboard Molding in Miami. You have to place both the boards on the wall so that it matches perfectly and secure the scarf joint with the wall near the stud location. You can use a miter saw to make the cuts and sand papers to smoother it. Remember not to over sand and make extra smooth so that the two boards slips.
For The Inside Corners
Usually, a coped joint is preferred for the corner joints in Baseboard Molding in Miami where you have to butt one board against the wall at ninety degrees and place the other one on the floor face down. Carefully tracing the profile with a pencil make the reference points to make the cope joints. Make the necessary cuts, at an angle of ninety degrees about one-sixteenth of an inch shorter than the profile. Finish the remaining cuts likewise with the help of the three square and half round files until all the pieces fit perfectly.
Joints For Outside Corners
Cutting miter joints for the outside corners are best for Baseboard Molding in Miami. When you do so you have to leave an extended portion of the first board at the outside corner joint, mark the place it would meet with the other piece with the tree-square. Cut the board at an angle of forty-five degrees, and test the fitting with a second piece by marking and cutting it in the same way and hammer it to the position. Similar care should also be taken when you encounter any doorways by measuring the distance between the door casing and the wall.
Fill The Gaps In
Now all your hard work would be of no value if there are noticeable and ugly gaps left behind. The gaps, which are imperative to remain after molding, should be carefully and painstakingly filled with the wood filler into the holes between the baseboards. When the wood filler dries up completely after some time, you should sand off the excess filler from the place and make it smooth to give that fine finish. Care should also be taken to fill up the gaps between the board and the wall with the caulk to give that perfect finish. For more information visit here: Architectural Moulding & Millworks
Use Scarf Joint Method
When you have to use more than one baseboard for the longest wall, then it is best done with the scarf joint method. You have to make the cuts at an angle of forty-five degrees for scarf joints in Baseboard Molding in Miami. You have to place both the boards on the wall so that it matches perfectly and secure the scarf joint with the wall near the stud location. You can use a miter saw to make the cuts and sand papers to smoother it. Remember not to over sand and make extra smooth so that the two boards slips.
For The Inside Corners
Usually, a coped joint is preferred for the corner joints in Baseboard Molding in Miami where you have to butt one board against the wall at ninety degrees and place the other one on the floor face down. Carefully tracing the profile with a pencil make the reference points to make the cope joints. Make the necessary cuts, at an angle of ninety degrees about one-sixteenth of an inch shorter than the profile. Finish the remaining cuts likewise with the help of the three square and half round files until all the pieces fit perfectly.
Joints For Outside Corners
Cutting miter joints for the outside corners are best for Baseboard Molding in Miami. When you do so you have to leave an extended portion of the first board at the outside corner joint, mark the place it would meet with the other piece with the tree-square. Cut the board at an angle of forty-five degrees, and test the fitting with a second piece by marking and cutting it in the same way and hammer it to the position. Similar care should also be taken when you encounter any doorways by measuring the distance between the door casing and the wall.
Fill The Gaps In
Now all your hard work would be of no value if there are noticeable and ugly gaps left behind. The gaps, which are imperative to remain after molding, should be carefully and painstakingly filled with the wood filler into the holes between the baseboards. When the wood filler dries up completely after some time, you should sand off the excess filler from the place and make it smooth to give that fine finish. Care should also be taken to fill up the gaps between the board and the wall with the caulk to give that perfect finish. For more information visit here: Architectural Moulding & Millworks
No comments:
Post a Comment